Latest release Page 1037
ANSYS® FloWizard™ ANSYS® FloWizard™ is a rapid flow modeling tool for Autodesk® Inventor™. This computational fluid dynamics (CFD) software is specifically built for design and process engineers who need to understand the detailed fluid dynamics of their designs. A user does not need to have extensive experience with complex computational models or meshes to succeed with FloWizard. Due to the decred learning curve, engineers can deploy flow simulation much earlier in the design cycle, realizing money-saving and design-enhancing benefits. In addition, FloWizard software can be implemented throughout an organization to address a wide variety of fluid dynamics design situations.Download a FloWizard®Overview Brochure Unlike other flow modeling tools, FloWizard™ automates tasks that usually require a lot of manual intervention, such as...
Displacement Based Design Traditionally, earthquake-resistant design has been strength-based, using linear elastic analysis. Since inelastic behavior is usually allowed for strong earthquakes, this is not entirely rational. Strength-based design considers inelastic behavior only implicitly. Displacement-based (or deformation-based) design considers inelastic behavior explicitly, using nonlinear inelastic analysis. Displacement-based design recognizes that in a strong earthquake, inelastic deformation (or ductility) can be more important than strength. PERFORM-3D allows you to use displacement-based design. Implementation of ASCE 41 Procedures for displacement-based design using inelastic analysis are specified in ASCE 41, “Seismic Rehabilitation of Existing Buildings”. ASCE 41 applies to the retrofit of existing buildings, but the procedures can be applied to the design of new buildings. PERFORM-3D implements the procedures in ASCE 41....
A completely revised and easy-to-use standalone interface that looks and feels like every other product in the Haestad Methods product line will make existing users of products such as WaterCAD, WaterGEMS, and StormCAD immediately feel comfortable developing transient analysis models in the new HAMMER. HAMMER uses the Method of Characteristics – the benchmark standard and unquestionably the most rigorous and robust algorithm for hydraulic transient flow analysis with over 20 years of proven real-world implementation. HAMMER’s all-new interface further simplifies the complex science of water hammer and transient analysis by implementing all the productivity and interoperability features that make Haestad Methods products the easiest to use in the industry. Key new features in HAMMER V8i (SELECTseries 4)HYDRAULICSModulating PRVs: Pressure reducing...
FeatureRECOGNITION is a powerful way to simplify and accelerate programming. By programming parts based on features in the CAD model, FeatureCAM streamlines machining and makes it easier to create and edit parts. FeatureCAM provides manual, interactive and fully automatic feature recognition (AFR). AFR identifies all 2D, 3D, Turn, Turn/Mill and Wire EDM features, including features that overlap or intersect. Features are fully associative with the CAD model so that design revisions are re-machined automatically. Ease of use is a guiding principal in the development of FeatureCAM. Graphical feedback, step-by-step wizards and tutorial-style animations run directly in the program dialog boxes. Ease of use has always been a FeatureCAM advantage and with feedback from our customers we continue to study ways...
Cadence Assembly Design Work Benchproduct:Cadence.ADW.v16.60.015 Lanaguage:english Platform:Linux Size:1DVD
Engineering change orders (ECOs) have a wide variety of implementations that range from adding or removing logic in a design to more subtle changes such as cleaning up routing for signal integrity. All ECOs are focused on delivering products to market as fast as possible with minimal risk to correctness and schedule. ECOs can be a time of high stress, long work hours, and uncertainty. Even if the logic change is implemented in the netlist, there might not be enough spare gates on the mask to implement the change. Benefits Provides faster turnaround time by minimizing manual intervention and eliminating time-consuming iterations Generates early estimates on ECO feasibility by quantifying designer intent Implements complex ECOs that are typically not attempted...
These new features include: Dynamic Parameter Estimation & Tuning – DPET GOST short-circuit – R 52735 standard New Web consoles for monitoring and predictive simulation Customizable Web console templates Native SCADA communications protocols Waveform capturing and synchophaser measurements New library merge and cable library quick-pick Enhanced analysis modules 3,500+ new device libraries Multi-language edition “ETAP 12.5 is the next logical step in our quest to deliver the most robust technologies to optimize and automate power system design while increasing the safety, quality, and productivity for which our products are known for around the world,” said Shervin Shokooh, Chief Operating Officer of ETAP. For example, prior to the availability of Dynamic Parameter and Estimation Tuning (DPET), users had to manually tune...
Fatigue damage is one the most common causes of structural failure, and can lead to disastrous outcomes. Therefore, prediction of structural fatigue life is essential in modern product design. P-EF (a.k.a. pro-EMFATIC for Femap) is a comprehensive fatigue analysis software package built on widely used fatigue calculation methods. P-EF calculates structural life, cumulative fatigue damage and safety factors. The stress and strain data used for fatigue calculations can be taken directly from Femap. The durability results can be stored back into Femap and can be displayed using Femap post-processing capability. It also provides add-on capabilities that allow users to calculate fatigue results using the test measurements or the analytical values from non-Femap solutions. P-EF’s fast, efficient, and accurate fatigue calculations...
Key new features in CivilStorm V8i (SELECTseries 3):INTEROPERABILITY Common file format with other Bentley sewer and stormwater products: With CivilStorm, StormCAD, SewerGEMS, and SewerCAD\’s new unified file format, the .stws file replaces the .csd, .stc, .swg, and .swc files. This common file format makes modeling teams’ workflows more efficient, since a model created in any one of these products can now be seamlessly opened and edited in another. Updated support for MicroStation: You can run CivilStorm from within MicroStation V8i (SELECTseries 3). A MicroStation license is required – if you don\’t have a MicroStation license, you can choose to run CivilStorm in its stand-alone mode. Updated support for AutoCAD: You can run CivilStorm from within AutoCAD 2014 (32- and 64-bit)....
New features in StormCAD V8iINTEROPERABILITY Common file format with other Bentley sewer and stormwater products: With StormCAD, CivilStorm, SewerGEMS, and SewerCAD\’s new unified file format, the .stws file replaces the .stc, .csd, .swg, and .swc files. This common file format makes modeling teams’ workflows more efficient, since a model created in any one of these products can now be seamlessly opened and edited in another. Updated support for MicroStation: You can run StormCAD from within MicroStation V8i (SELECTseries 3). A MicroStation license is required – if you don\’t have a MicroStation license, you can choose to run StormCAD in its stand-alone mode. Updated support for AutoCAD: You can run StormCAD from within AutoCAD 2014 (32- and 64-bit). An AutoCAD license...