EDA Design Page 55
ANSYS Electronics Suite 2021 R1 For linux&Win ANSYS is the leading provider of electromagnetic simulation software, engineers rely on our electromagnetic field solvers and system simulation products to design communication and networking systems, integrated circuits (ICs), printed circuit boards (PCBs) and electromechanical systems. ANSYS signal integrity analysis products are ideal for designing high-speed serial channels, parallel buses and complete power delivery systems found in modern high-speed electronic devices. Our RF and Microwave design and simulation software enables engineers to design, simulate and validate high-frequency components and antennas found in communication systems, mobile devices, computers, radio and radar. ANSYS electromechanical simulation software is ideal for the design of electromechanical and power electronics components and systems common to the automotive, aerospace and...
NI FlexLogger 2021 R1 National Instruments (NI), is pleased to announce the availability of FlexLogger 2021 R1 is application software for quick sensor configuration and data logging of mixed signals to verify electromechanical systems, all without programming. FlexLogger 2021 R1 – Date: December 2020 New Features 2021 R1 (December 2020) – Added support for USB X Series devices. Refer to the Supported Hardware section for specific model support information. – Added support for PXIe X Series counters. – Drive DAQ output signals non-deterministically by mapping to another channel. – Use test properties as placeholders in file names and locations. – Automate FlexLogger with the Python-based FlexLogger Automation API. – Onboard counter support for CompactDAQ chassis. – Analyze logged data with...
Remcom XGTD 2019 Accurate calculation of RCS at millimeter wave frequencies requires sufficiently detailed geometric representation of the target and physical modeling techniques that capture the scattering effects of small facets. Highly detailed facet models and traditional methods for calculating RCS at these frequencies can often result in very long run times. Using Remcom’s X3D with Physical Optics (PO) and Method of Equivalent Currents (MEC) model for calculating RCS, accurate results can be achieved within reasonable run times. This example details the setup and execution of RCS calculations using XGtd’s X3D PO MEC model and compares the predictions to those made using XFdtd. The target is a Hellfire missile, which was imported into XG from a KMZ file. Figure 1...
NI TestStand 2020 v20 The LabVIEW development team is pleased to announce the availability of TestStand 2020 version 20.0.0 is a flexible and open test management framework for building, customizing, and deploying a full-featured test management system. TestStand 2020 New Features The following list summarizes the new features in TestStand 2020 and other changes since TestStand 2019: – TestStand Sequence Editor Visual Design Updates – Python Adapter Improvements – Regular Expression Support – InstrumentStudio Integration Improvements TestStand Sequence Editor Visual Design Updates TestStand 2020 introduces a streamlined visual design to the TestStand Sequence Editor. In addition to cosmetic changes, the sequence editor has the following changes: – By default, the sequence editor toolbar now only displays buttons that are global...
Mentor Graphics ModelSIM 2020.4 In addition to supporting standard HDLs, ModelSim increases design quality and debug productivity. ModelSim’s award-winning Single Kernel Simulator (SKS) technology enables transparent mixing of VHDL and Verilog in one design. Its architecture allows platform-independent compile with the outstanding performance of native compiled code. The graphical user interface is powerful, consistent, and intuitive. All windows update automatically following activity in any other window. For example, selecting a design region in the Structure window automatically updates the Source, Signals, Process, and Variables windows. You can edit, recompile, and re-simulate without leaving the ModelSim environment. All user interface operations can be scripted and simulations can run in batch or interactive modes. ModelSim simulates behavioral, RTL, and gate-level code, including...
IAR Embedded Workbench for Microchip AVR v7.30.3 IAR Embedded Workbench for AVR is a complete set of powerful C/C++ development tools with extensive support for AVR Microcontroller families. IAR offers a completely integrated development environment incorporating a compiler, an assembler, a linker and a debugger. IAR Embedded Workbench for AVR features world-leading code optimizations that create compact, fast-performing code. The optimization technology is continuously improved. These powerful optimization technology enable developers to gain even better performance in applications where optimal execution speed is critical. To achieve the best possible configuration for the application at hand, developers are able to tune the optimizations. With the possibility to set different optimizations for different parts of the code, the right balance between code size...
IAR Embedded Workbench for ARM 8.50.9 IAR Embedded Workbench for Arm®, an integrated development environment, and the included IAR C/C++ Compiler generates the fastest performing, most compact code in the industry for Arm®-based applications. C-SPY Debugger, is a fully integrated debugger with performance analysis, power visualization and RTOS awareness. Configuration files, code examples and project templates are included. Feature list: Leading optimization technology creates smaller, faster, smarter code Comprehensive debugging functionality Static and runtime analysis available through add-ons Power debugging for minimized power consumption
PentaLogix.CAMMaster.v11.18.1 PentaLogix\’s most complete CAM software designed to meet tomorrow\’s manufacturing needs. CAMMaster uses scripting, raster and contour based algorithms and increased ease-of-use to deliver the strongest PC-Based CAM system in the industry. We provide you a USB dongle. CAMMaster can be installed on multiple computers but will only run on a computer that has the dongle plugged in. *Upgrade Option: If you already have a license of CAMMaster and are looking to purchase an Add-On Module, please select the option that indicates you already have a license of CAMMaster and proceed to Add-On Modules section to make your selection. You will also be asked to enter the Serial Number of your existing license. Product:PentaLogix.CAMMaster.v11.18.1 Lanaguage:english Platform:Win7/WIN10 Size:1CD
Mentor.Graphics.Calibre.2020.3.16.11 For linux The next few IC technology nodes will be more challenging than any other transition since the first integrated circuit. Until the 32 nm node, distortions involved in making the masks using 193 nm lithography were small and had little impact since mask features are four times larger than the actual features on a die. Traditional OPC has mainly addressed the wafer image transfer and only included mask making effects as a part of the overall OPC model. But at 32/22 nm, mask fabrication is subject to the same imaging limitations that have affected wafer lithography since the 130 nm node. Areas of particular sensitivity include narrow features and corners, residual proximity and linearity effects due to etch...
IAR Embedded Workbench for Renesas RX v4.20.1 Release notes for IAR Embedded Workbench for Renesas RX version 4.20.1HighlightsC-STAT enhancementsMISRA C:2012 Amendment 1The static analysis tool C-STAT has extended its coverage of the MISRA C:2012 Coding Standard and now fully supports MISRA C:2012 Amendment 1. This amendment adds 14 additional rules to MISRA C:2012 with a focus on security concerns highlighted by the ISO C Secure Guidelines. Several of these address specific issues pertaining to the use of untrustworthy data, a well-known security vulnerability.Extended coverage of CERT CThe static analysis tool C-STAT has extended its coverage of the SEI CERT C Coding Standard. The SEI CERT C Coding Standard\’s goal is to provide rules for developing safe, reliable, and secure systems...